Direkt zum Inhalt

Jab Troubleshooting Checklist

Compatibility

Shifter & Cassette Pairing (Jab Cams)
2x / 3x
UDH & T-Type
  • UDH is a term referring to the frame and hanger fitment standard.
  • T-Type is a term that Madrone uses to refer to cassettes.
  • T-Type cassettes are unique because they have a 2.5mm offset compared to other cassettes.
  • T-Type cassettes require a UDH frame.
  • T-Type cassettes require the Jab T-Type Mount.
Frames & Jab Mounts
  • Standard mount fits any frame.
  • If your frame is not UDH, you need to use the standard mount.
  • If your frame is UDH, you can use any mount, but T-Type cassettes require the T-Type mount.
  • Stiffener plate mounts increase the strength, but you need a UDH frame.
  • Mounts explained here.
Hangers
  • If your frame does not have a UDH hanger, the Jab standard mount is the only one that will fit.
  • Some non-SRAM UDH hangers might not fit properly due to alternate dimensions of the bolts.
  • If you have a T-Type cassette, the T-Hanger is needed (also only for UDH frames).
Cassettes & Jab Cages
  • Long cage: Max cog of 52 teeth.
  • Short cage: Max cog of 45 teeth.
  • DH cage: Max cog of 28 teeth.
  • Cages explained here.
Chain Length and Type
  • Chain length is important.
  • Refer to the guide here.
  • The chain should be compatible with your cassette.
  • The Jab is compatible with all 12 speed and 11 speed chains.
Chain Offset
  • The chainring offset should be set for the rear hub and cassette combination.
  • Make sure your chain line matches the manufacturer specifications.
Chainstay Length
  • This is the distance from the bottom bracket to the rear wheel axle.
  • Longer is better for good chain meshing (low noise and low friction).
  • If the chainstay length is too short, the lower pulley of the derailleur might not mesh well.
Wheel Size

The Jab works well with these wheel sizes:

  • 32"
  • 29"
  • 700c
  • 27.5"
  • 26"

Smaller wheels are not recommended due to chainstay length and cage length.

Friction

Chain
  • Keep your chain cleaned and lubricated.
  • Lubricate your chain after cleaning it.
  • While you clean, place a clean rag over your brake caliper and rotor to prevent oil from spraying onto them.
Cassette
  • Brush the gunk off the cassette regularly.
  • While you brush, cover the brake rotor with a clean rag to prevent oil from spraying onto it.
Chainring
  • Clean the gunk off the teeth of the chainring periodically.
Bottom Bracket
  • Brush grit off the bottom bracket seals periodically.
  • If the cranks do not spin freely with no chain attached, you may need to rebuild or replace your bottom bracket.
Rear Wheel Hub
  • Make sure your freehub ratchets freely. It should never drive the chain when the wheel is freewheeling.
Cable and Housing
  • Shift cable comes in 2 diameters: 1.25mm or 1.10mm. Fat cable won't work in housing for thin cable.
  • Check for cable and housing friction by shifting with no derailleur attached to the cable.
  • Replace cable and/or housing if there is any noticeable friction.
Cable Pulley
  • Remove, clean, and grease the inside diameter of the cable pulley if you think it is affecting shift quality.
Derailleur Pulleys
  • Periodically remove, clean, and re-grease the derailleur pulley bearings.
  • Packing the dust shields with grease will make the bearings last a long time.
Derailleur Link Pivots
  • The Jab ball bearing link pivots are outstanding at eliminating friction.
  • If you have a Jab with bushing pivots, we recommend to update to the ball bearing links. Email support@madronecycles.com for details.
Derailleur Cage Pivot
  • Rotate the cage by hand to make sure the only friction source is the clutch.

Installation

Cage Lock
  • To remove the wheel, the cage can be locked in an open position by inserting a tool.
  • Use a T25 of 4mm hex.
Mounting
  • When the M10 mounting bolt is tight, the Jab can rotate, but with a lot of friction (this is intentional).
  • If you have a stiffener plate, alternate the tightening process of the mounting bolt and hanger bolt.
  • Hanger bolts (not M10 mounting bolts) are usually reverse thread.
Installing Chains
  • If the chain is not broken, remove the upper pulley and lower cage spacer to route the chain.
  • Make sure the wide teeth of the pulleys are in the wide links of the chain.
  • Make sure the chain is not routed around the upper cage spacer.
Cable Pinch
  • Before pinching the cable, run the barrel adjuster all the way in so you don't run out of adjustment range.
  • Pinch the cable under the washer.
  • Route the cable rearward (not outward).
  • There are 2 groove options for rearward routing.

Chain Length & B Gap

Chain Length (Important)
  • Chain length is important.
  • If the cage is rotated really far forward in the large cog, the chain length might be too short.
  • Watch the video guide here.
B Gap
  • If the B screw is turned in really far to achieve the right B gap, the chain length might be too long.
  • The B screw has a jam nut to lock the adjustment in place. It cannot be adjusted when the jam nut is tight.
  • Watch the video guide here.
DH Jab Specifics
  • We recommend following the guide here when installing the DH Jab.
  • However, more discretion can be used to achieve the right chain length and B gap.
  • Make sure the suspension does not pull the chain and cage too tight at bottom out.
  • If the B gap is larger than the guide states, that is OK but make sure it shifts well.

Final Adjustments

Limit Screws
  • Small cog limit screw: Located on the "inside" of the Jab.
  • Large cog limit screw: Located on the "outside" of the Jab.
  • Set the small cog limit screw so the Jab can shift to and from it, and there is little-to-no slack in the cable.
  • Set the large cog limit screw so the Jab can shift to and from it, but not allow the chain to go into the spokes.
Indexing / Barrel Adjustment
  • Flat bar shifters (MTB Jabs) have barrel adjustment on the shifter.
  • Drop bar shifters (gravel Jabs) has the barrel adjustment on the derailleur.
  • Before pinching the cable, run the barrel adjuster all the way in so you don't run out of adjustment range.
  • Set the barrel adjuster so the shift quality and speed are about equal in both directions.

Alignment

Symptoms of Bends
  • Bends in the hanger or derailleur can cause the shift quality to be bad at 1 end of the cassette but not the other. (Or the middle vs the ends).
  • Other issues can cause this, but if you ruled out all other issues, a bend is likely.
Bent Hanger
  • It is wise to make sure your hanger is not bent or installed crooked, even if it is new.
  • This requires a hanger alignment tool.
Bent Derailleur
  • A bend in one or more parts of the derailleur will hurt shift quality.
  • It is usually hard to see slight bends.
  • Contact us if you need help checking for bends.

Noises

Chain Meshing
  • Make sure wide pulley teeth are not in the narrow links of the chain.
  • If the pulley meshing noise is abnormal at the outer cogs on the cassette, review the Compatibility and Chain Length & B Gap sections.
Creaking
  • On bicycles, creaking can happen at any joint where 2 parts are in contact and transmit force.
  • Creaking can be eliminated by rebuilding, cleaning, and re-greasing.
  • The joints to check on the Jab are:
  1. Mounting bolt assembly
  2. Link pivots
  3. Cable pulley
  4. Cage attachment

Removal Tips

Cable Removal
  • If you don't want to risk fraying the cable, you can loosen the cable pinch screw, remove the cam, and remove cable pulley bracket.
  • The Jab will come off but the cable parts will stay on the bike.
Removing Chains
  • No need to break the chain if its intact on the frame.
  • Remove the Jab upper pulley and lower cage spacer to remove the chain.
Back to top